ADM-201 dump PMP dumps pdf SSCP exam materials CBAP exam sample questions

自制宠物饮水池 – 译学馆
未登录,请登录后再发表信息
最新评论 (0)
播放视频

自制宠物饮水池

Diy ● DOG CAT water dispenser HACK ● self filling

大家好! 今天我要向你们演示的是
Hi, everyone! Today I’m gonna show you how
如何把桶装水壶
to take a water dispenser bottle and make it
改造成适合几只宠物同时使用的饮水站
into a multi-pet watering station that
而且自带添水功能
automatically fills all by itself.
[水声]
[water splashing]
这个装置能保证你的宠物在很长时间都有水喝
This make sure that they have water over a long period of time
而不用担心它们的水碗总是空空如也
without worrying about any of the bowls going dry.
[敲击键盘]
[tapping on keyboard]
所以 要完成这个项目 你需要
So what you’re gonna need for this project
一个桶装水壶
is a water dispenser bottle.
这个容量为19升
This one is 19 litres.
和一个塑料托盘。 深度 重量随意
And a plastic tray. It can be any depth and weight
不需要像这个这么浅 可以再深点
It doesn’t have to be this shallow, it can be deeper.
只要有足够宠物们饮水的空间就行
As long as you got lots of room for all your pets to get a drink.
还有两只2升装饮料瓶
And two 2-litre pop bottles
你可以使用手头的任意饮料瓶
You can pretty well use any pop bottle you have
只要是装碳酸饮料的就行
as long as it holds carbonized beverage
上面的盖子看着不咋地
These caps are very cheap looking but
但其实密封效果奇佳
they seal really well.
所以呢 我们要做的第一件事就是在这加个盖子
So the first thing we want to do is put a lid on here.
这样我们就能随意把它取下 灌水
So that we can undo it, fill it up easily
再拧上盖子 就达到了完全密封的效果
and we put the lid back on, it seals completely
因为这种盖子绝不会漏水
cause it can’t have any leaks here what so ever.
拿出一只2升饮料瓶 从这个位置切下盖子的部分
Get one of the two 2-litre pop bottles and cut the lid off right here.
能看到这里是桶装水壶盖子的位置
So these water dispenser bottles have lid here
这里有凹进去的部分
and has little indentation right in there.
我们要把这部分切掉
And we want to cut this piece here off
这样它就能放进壶口
so that it fits just underneath…
正好卡在这里
snap right in there quite nicely.
然后我们要做的是 把它倒置
So what we are gonna do it’s to put this thing upside down.
标上记号 接着切除余下部分
And make some marks and then we cut off the access.
先试着装上看看效果。 然后拿好
And then test fit it. So just take it
往里塞
and squeeze it around
直到卡进去为止
until you get it to pop in there.
就这样
Just like that.
现在我们往这里挤入硅胶 进行密封
So now we just wanna put a bit of silicone in here to seal it up.
通用型硅胶即可
Just use regular All Purpose silicone.
CLEAR牌就不错 越便宜越好
The CLEAR staff is good and the cheaper, the better.
现在拿住切下的瓶子口
Now just take your top bottle piece
将其滑入硅胶
and slip it into the silicone.
进入后稍微往上提
And once it’s in there just left it up
放置入位
and sit it into position.
稍微转动一下 使硅胶密封
give it a twist to help the silicone to seal.
接下来围绕瓶子接口的部分
And then any of the access right here
拿住顶部
just hold this up and
用一根手指将硅胶摸匀
use one finger and smooth it all out
以此完成外圈的密封
and then just use it to seal up all way around
因为我们不希望在这个部分
cause we don’t want have any air leak or whatsoever
发生漏气
around this part.
然后取出第二个2升饮料瓶
Now take the second 2-litre pop bottle and cut
从凸起的部分切下瓶子口
the top off just underneath this flange
现在用砂纸打磨
So now we just want to take off that razed area
不平整的部位
with a bit of sand paper.
下面要做的是 在桶装水壶
Next thing we want to do is we want to drill a hole
底部中间钻孔
in the bottom of the bottle.
拿上饮料瓶组件
So take your pop bottle piece and
在拟安装的位置做好记号
just mark where it’s going to go.
在中间位置钻一个半英寸的洞
And drill a half inch hole in the center.
[钻孔]
[drilling]
这里涂上硅胶
Now put a bit silicone on here.
然后静置24小时 使硅胶凝固
Now just let the silicone secure over the next 24 hours.
已经到时间了 你能看到
So it has been 24 hours now you can see
这部分粘地十分牢固
how this has adhered in here really well.
加水的时候 我们必须确保
As filling it, we want to make sure we don’t demage
不会损坏壶口上的盖子
the lip on top of the bottle.
加满水后 将整个装置放倒以确保
So when you have it full, lay on its side to make sure
壶口的位置没有漏水
you don’t have any leaks whatsoever on the top.
一旦竖直地放入托盘
Once this is in the tray and standing up
我们可不希望顶部漏气
we don’t want air leaking into the top here.
因为如果漏气的话 水就会漫过托盘
Cause if it does it’ll over fill the tray and
洒的满地都是
leak out.
所以我们拿好水壶
So we just take the water bottle and
放入托盘
put it in the tray.
建议大家不要把开口
And I suggest instead of putting
对着前面
the openning towards the front
你的宠物可以 也可能会啃食这个位置
where pets can, maybe chew at it.
可以把开口对着其中一个角
you can put it towards one of the corners.
放好后 取下盖子
After it’s in position, just take off the cap
托盘就回自动添水
and let the tray fill itself up.
你能看到 一旦水位淹没水壶开口处
You can see that the water stop coming out
就不再往外流了
as soon as it got to the top of the openning of the bottle.
你们可能会想 这是干什么的
You’re probably wandering what is this for.
我从另一个饮料瓶上切下头部
Well I cut the top off another pop bottle
然后可以把从壶上取下来的盖子
and that is where I can park the cap
再拧在这里
once I take it off the bottle.
希望本视频对你有帮助
Well I hope this video is help.
如果喜欢的话 请点击按钮订阅我的频道
If you like it, hit the light button and subscribe to my channel.
下次见咯!
And we’ll see you next time.

发表评论

译制信息
视频概述
听录译者

WeiRan

翻译译者

WeiRan

审核员

自动通过审核

视频来源

https://www.youtube.com/watch?v=yx3ZJJ9zbQs

相关推荐